Request An Estimate

 

 

This great article in the next paragraphs in relation to A Step-by-Step Guide to Installing a Bathtub is indeed entertaining. Don't miss it.

Installing a bath tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is additionally a reasonably difficult task. If the old tub is readily available, the task can move quickly; if you need to open up a wall to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the task and fit attempting it. Rather than working with a contractor to take control of a halfway-completed project, it is far better to think about using one before you start. Chances are you may require an expert plumber to make tube links.
This post will certainly help you mount a new tub in your bathroom if you have currently purchased a brand-new tub as well as do not need to transform the arrangement of your previous water pipes.
Your devices and also material list should make up the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Planning for the Installation

First of all, the sustaining frame supplied with the bathroom should be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to prevent stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.

 

 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water system. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be rather troublesome because of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Prior to carrying on to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Setting up the Bathtub

Using both wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to make certain that the tub is leveled all round. This can be attained by checking the spirit level and also changing the feet on the tub until the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Turn on the water supply and also inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Load the tub and additionally inspect the overflow outlet as well as the normal electrical outlet for leakages.
Lastly, deal with the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub must wait until the bath tub has been made use of a minimum of when as this will resolve it into its final setting.

 

 

Fitting New Taps

If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin ensuring that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the tap is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type needs to be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bath tub

In the area where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bath and the tiling, causing difficulties with wetness and feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes as well as cartridges, as well as are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water before sealing, to allow for the motion experienced when the tub remains in usage. The sealer can fracture rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Hopefully you liked our section on Tools You Need to Install a New Bathtub . Thank you for spending some time to read through our blog. Liked our piece? Please share it. Help somebody else locate it. We treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.

Schedule Now!