We've found this post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround listed below on the internet and figured it made perfect sense to write about it with you in this article.
Installing a bath tub isn't specifically brain surgery, however it does require solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately difficult task. If the old bathtub is easily available, the project can relocate immediately; if you have to open a wall surface to eliminate the old tub and place the new bathtub, the job is a lot harder. In either instance, the job is within a home handyman's abilities, although you will certainly require an assistant to leave the old tub and also embeded in the new one. See to it you have actually qualified on your own for the task and fit trying it. Instead of employing a contractor to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you start. Chances are you might need an expert plumber to make tube connections.
This post will aid you set up a new tub in your bathroom if you have currently purchased a brand-new tub and also don't require to alter the setup of your previous water system pipes.
Your devices and product checklist must consist of the following:
- New Tub
- Hammer
- Pipeline Wrenches
- Prybar
- Safety Glasses
- Degree
- Pliers
- Adjustable Wrench
- Putty Blade
- Screwdriver
- Cold Chisel
- Measuring tape
- Pipe Caps
Planning for the Installation
First of all, the supporting framework provided with the bath needs to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to stop pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you use all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing taps can be quite problematic due to the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub until the spirit level reviews degree.
To set up taps, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
Switch on the water and also inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bathroom paneling as defined in the producer's instruction manual. Tiling and also securing around the bathtub needs to wait up until the bathtub has actually been utilized a minimum of when as this will certainly settle it right into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place in between the tap and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill up the tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can crack relatively very early if you do not think about this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
Hopefully you enjoyed our piece about Installing A Bathtub. Thanks so much for taking time to read through our content. In case you liked our blog posting if you please make sure you remember to share it. Thanks so much for taking the time to read it.
Schedule A Free Estimate
Comments on “Exactly How to Remove and Change a Bathtub.”