Course Detail

 

 

Just how do you actually feel on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Installing a tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is additionally a reasonably challenging job. If the old tub is conveniently easily accessible, the project can relocate immediately; if you have to open up a wall surface to remove the old bathtub as well as position the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly require a helper to move out the old bathtub and embeded in the new one. See to it you have actually qualified on your own for the job and also are comfortable trying it. Rather than employing a professional to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Possibilities are you may require a professional plumber to make tube links.
This post will aid you set up a brand-new tub in your restroom if you have actually already acquired a new bathtub as well as don't require to change the setup of your previous supply of water pipelines.
Your tools and also material list must comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Preparing for the Installment

Firstly, the sustaining frame provided with the bath must be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last position.

 

 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is detach the water. After doing so, activate the faucets to drain any water remaining in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted gain access to that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Before proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.

 

 

Setting up the Bathtub

Using both wood boards under its feet, put the tub in the needed position. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by checking the level as well as changing the feet on the bathtub till the level checks out level.
To mount faucets, fit the bottom of the furthest versatile tap port to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as inspect all joints and brand-new pipework for leaks and tighten them if needed. Fill up the bathtub as well as likewise examine the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, repair the bath paneling as defined in the producer's user's manual. Tiling as well as sealing around the bath tub should wait till the bathtub has actually been utilized at least when as this will resolve it into its last position.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washing machines remain in place in between the tap as well as the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind should be linked to the tap ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Bathtub

In the location where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, resulting in issues with wetness and also possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can break relatively very early if you do not take into account this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles making use of waterproof or water-proof adhesive and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a serious person who reads about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that information was essential. Appreciated our post? Please share it. Let other people discover it. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Schedule Appointment Now